{"id":13573,"date":"2026-07-27T21:51:21","date_gmt":"2026-07-27T13:51:21","guid":{"rendered":"https:\/\/raymonvalve.com\/product\/non-slam-check-valve\/"},"modified":"2026-07-29T17:11:43","modified_gmt":"2026-07-29T09:11:43","slug":"non-slam-check-valve","status":"publish","type":"product","link":"https:\/\/raymonvalve.com\/pt\/product\/non-slam-check-valve\/","title":{"rendered":"V\u00e1lvula de reten\u00e7\u00e3o n\u00e3o-slam"},"content":{"rendered":"
\n
\n
\n
Engineering scope<\/div>\n

Define the application boundary for Non Slam Check Valve<\/h2>\n

A Non Slam Check Valve is evaluated for automatic reverse-flow prevention. Forward flow opens the closure element and decreasing or reversing flow closes it. Dynamic response depends on velocity, travel, inertia, spring force, orientation and the system transient.<\/p>\n

Use the name as a starting point. Technical approval still depends on reduced reverse velocity through controlled short-travel closure, the complete service envelope, installed interfaces and measurable acceptance.<\/p>\n

\n
\n

Non Slam<\/h3>\n

Reduced reverse velocity through controlled short-travel closure. Provide pump coast-down, line profile, fluid properties, velocity and surge acceptance criteria.<\/p>\n<\/div>\n

\n

Application envelope<\/h3>\n

Confirm every pressure, temperature, differential-pressure and cycling case for this Non Slam Check Valve.<\/p>\n<\/div>\n

\n

Installed interface<\/h3>\n

Verify ends, bore, flow direction, orientation, operator envelope, loads and maintenance access.<\/p>\n<\/div>\n

\n

Order-specific boundary<\/h3>\n

Website content is not tag-level certification. Suitability and supplied scope are established only by the accepted quotation, datasheet and drawing.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n
Specification workflow<\/div>\n

Connect each selection decision to a controlled record<\/h2>\n

The table turns application inputs for Non Slam Check Valve into review points and tag-linked evidence.<\/p>\n

\n\n\n\n\n\n\n\n\n\n
Review area<\/th>\nEngineering question<\/th>\nRequired record<\/th>\n<\/tr>\n<\/thead>\n
Opening margin<\/td>\nMinimum, normal and maximum flow must keep the closure stable without excessive pressure loss.<\/td>\nFreeze the accepted value in the tag datasheet and verify it on the approved drawing.<\/td>\n<\/tr>\n
Closing response<\/td>\nReverse velocity and deceleration rate should be evaluated where surge or slam is consequential.<\/td>\nResolve the open point before release and retain tag-specific evidence in the final dossier.<\/td>\n<\/tr>\n
Orientation<\/td>\nHorizontal, vertical-up or other installation positions must be permitted by the selected design.<\/td>\nState the measurable requirement and connect it to a drawing, procedure or test result.<\/td>\n<\/tr>\n
Maintenance access<\/td>\nDisc, hinge, spring, guide and seat inspection requirements influence body style and location.<\/td>\nState the measurable requirement and connect it to a drawing, procedure or test result.<\/td>\n<\/tr>\n
Non Slam<\/td>\nProvide pump coast-down, line profile, fluid properties, velocity and surge acceptance criteria.<\/td>\nCapture the selection basis, approved deviation if any and the record used for acceptance.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Record exact standard designations and contract editions; resolve scope gaps and purchaser options before manufacture.<\/p>\n<\/div>\n<\/section>\n

\n
\n
Application boundaries<\/div>\n

Application limits to examine before technical approval<\/h2>\n

The label \u201cnon-slam\u201d is not a system guarantee; pump coast-down, line profile and fluid compressibility govern the transient. Also review orientation, transients, cycling, contamination, access and consequences of internal or external leakage.<\/p>\n

\n
Fluid composition plus minimum, normal, maximum, startup and upset cases for the Non Slam Check Valve<\/div>\n
Valve role, operating cycles, permitted leakage, safe state and consequence of failure<\/div>\n
Pressure class, size, end connection, face-to-face and piping-interface requirements<\/div>\n
Body, trim, seat, packing, bolting, lining or coating materials as applicable<\/div>\n
Manual or actuated operation, maximum load, fail action, speed, utilities and accessories<\/div>\n
Exact standards and editions, ITP points, material\/NDE\/pressure\/leakage tests and turnover index<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
Evidence and quality<\/div>\n

Make every critical claim traceable to the valve tag<\/h2>\n

Evidence should identify the supplied configuration, revision, heat or lot and applicable test procedure. Use the valve standards guide<\/a> to separate product, rating, dimensional, end-connection and test scope.<\/p>\n

\n
\n

Design basis<\/h3>\n

Tag requirements, design review, materials list and approved exception register.<\/p>\n<\/div>\n

\n

Material identity<\/h3>\n

Tag-to-component material mapping with certificates, processing records and identity checks.<\/p>\n<\/div>\n

\n

Inspection and tests<\/h3>\n

Hold\/witness records, material\/NDE\/pressure\/leakage\/functional results and nonconformance closure.<\/p>\n<\/div>\n<\/div>\n

Non-slam performance is a system result, not a nameplate property.<\/p>\n

No statement here is an unqualified certification claim; standards, editions and evidence remain subject to project review.<\/p>\n<\/div>\n<\/section>\n

\n
\n
RFQ checklist<\/div>\n

Information needed for a tag-level technical offer<\/h2>\n

Provide a controlled valve list or datasheet covering every operating case, interface, material, operation, standard, inspection, test and document requirement.<\/p>\n

For a Non Slam Check Valve, also highlight reduced reverse velocity through controlled short-travel closure. Keep an open-point register for any item that could change safety, function, cost or delivery.<\/p>\n

\n
\n

Turn the datasheet into a clarified quotation basis<\/h2>\n

Provide the actual application; the response will separate confirmed requirements from assumptions and identify the checks still required.<\/p>\n<\/div>\n

Submit Your Datasheet<\/a>Compare Check Valve Options<\/a><\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
Related engineering route<\/div>\n

Follow the product, application and inspection route<\/h2>\n
<\/p>\n

Product family<\/h3>\n

Compare the main constructions and selection boundaries in this valve family.<\/p>\n

<\/a><\/p>\n

Project Valve Review<\/h3>\n

Resolve interacting pressure, temperature, corrosion, wear or project risks.<\/p>\n

<\/a><\/p>\n

Testing and inspection<\/h3>\n

Define pressure-test scope, acceptance, instruments, witness points and records.<\/p>\n

<\/a><\/div>\n<\/div>\n<\/section>\n

<\/p>\n