D971X Wafer Butterfly Valve selection starts with the service duty
A D971X Wafer Butterfly Valve is evaluated for compact quarter-turn isolation or regulation. A disc rotates within the body and piping bore. Offset geometry, seat construction, shaft support, flange interface and actuator torque determine sealing, wear and controllability.
Before quoting this configuration, close compact installation between flanges with disc-clearance and gasket controls and record all process, mechanical, operating and documentation assumptions.
Wafer
Compact installation between flanges with disc-clearance and gasket controls. Confirm flange type, inside diameter, gasket, bolt arrangement, pipe schedule and removal access.
Application envelope
Confirm every pressure, temperature, differential-pressure and cycling case for this D971X Wafer Butterfly Valve.
Installed interface
Verify ends, bore, flow direction, orientation, operator envelope, loads and maintenance access.
Order-specific boundary
Published information supports initial screening; final size, class, materials, trim, operation, tests and documents are fixed in approved order records.
Published configuration data for D971X Wafer Butterfly Valve—confirmation required
The values below are transcribed from the previous public product listing so useful model information is not lost during the quality rebuild. They are not a universal available range, certificate or order commitment. Confirm every value in the accepted quotation, tag datasheet and approved drawing.
| Parameter | Previous listing | Required order check |
|---|---|---|
| Product type | Not stated in the previous public listing. | Confirm the exact model, construction and supplied configuration. |
| Nominal size / DN | Not stated in the previous public listing. | Confirm each ordered tag and available trim or bore combination. |
| Pressure rating | Not stated in the previous public listing. | Confirm governing rating standard, class and temperature basis. |
| Temperature | Not stated in the previous public listing. | Confirm design, operating, startup and upset metal temperatures. |
| End connection | Not stated in the previous public listing. | Confirm standard, facing, schedule, bore and mating interface. |
| Flow coefficient / characteristic | Not stated in the previous public listing. | Confirm calculated cases, trim, travel and installed behavior. |
| Body / bonnet material | Not stated in the previous public listing. | Confirm component grade, product form, heat treatment and records. |
| Trim / closure material | ductile iron, stainless steel, corrosion-resistant steel, titanium steel, copper alloy; valve seat: D , ethylene propylene glycol, neoprene, Hyporon, PTFE, natural rubber, etc. The electric soft-seal butterfly valve adopts a variety of parts and materials, and | Confirm every wetted component, hardness, coating and pairing. |
| Seat / seal material | Not stated in the previous public listing. | Confirm compatibility, leakage criterion and pressure-temperature limit. |
| Operation / actuator | Not stated in the previous public listing. | Confirm worst-case load, fail state, utilities, speed and accessories. |
| Leakage basis | Not stated in the previous public listing. | Confirm standard, edition, test direction, medium and measurable acceptance. |
Evidence boundary: where the previous listing was incomplete or awkwardly translated, this page does not guess a value. Raymon Valve should replace provisional web data with the controlled product datasheet when it is available.
Connect each selection decision to a controlled record
Use the matrix to close decisions often hidden behind the short description “D971X Wafer Butterfly Valve.”
| Review area | Engineering question | Required record |
|---|---|---|
| Disc and seat geometry | Concentric, double-offset or triple-offset construction must match shutoff and temperature duty. | Capture the selection basis, approved deviation if any and the record used for acceptance. |
| Piping interface | Wafer, lug, flanged or welded bodies require compatible flange dimensions, gaskets and disc clearance. | Make this requirement auditable through the order datasheet, design review and inspection plan. |
| Torque basis | Seating, bearing, packing and hydrodynamic torque must be checked at every operating case. | Name the controlling document, responsible reviewer and inspection or calculation record. |
| Flow duty | On-off, throttling, minimum opening and velocity limits should be stated. | Name the controlling document, responsible reviewer and inspection or calculation record. |
| Wafer | Confirm flange type, inside diameter, gasket, bolt arrangement, pipe schedule and removal access. | Name the controlling document, responsible reviewer and inspection or calculation record. |
Check standards and acceptance criteria against the purchaser-approved edition before order release.
Application limits to examine before technical approval
Check disc clearance, installation orientation and transient loads; a nominal flange fit does not prove that the disc can open safely. Installed behavior can be governed by flow dynamics, deposits, operating frequency, maintenance access and the response to abnormal conditions.
Make every critical claim traceable to the valve tag
Evidence should identify the supplied configuration, revision, heat or lot and applicable test procedure. Use the valve standards guide to separate product, rating, dimensional, end-connection and test scope.
Design basis
Approved datasheet, drawing, bill of materials, rating basis and documented deviations.
Material identity
Pressure and wetted-part traceability plus welding, heat treatment, hardness and inspection evidence.
Inspection and tests
Hold/witness records, material/NDE/pressure/leakage/functional results and nonconformance closure.
A wafer body may not provide independent downstream isolation; piping procedures must reflect the design.
No statement here is an unqualified certification claim; standards, editions and evidence remain subject to project review.
Data to send for a technically complete quotation
Provide a controlled valve list or datasheet covering every operating case, interface, material, operation, standard, inspection, test and document requirement.
For a D971X Wafer Butterfly Valve, also highlight compact installation between flanges with disc-clearance and gasket controls. Keep an open-point register for any item that could change safety, function, cost or delivery.
Ask for a configuration tied to the real duty
Send the valve list and project requirements. Raymon Valve will identify missing inputs, clarify construction and return an order-specific quotation basis.
Connect this configuration with family and quality guidance
Convert D971X Wafer Butterfly Valve from a broad request into an auditable engineering decision
This section addresses the decision a visitor is likely trying to complete—not merely the meaning of the page title. Use it to identify required inputs, compare the proposal and specify the record that will prove acceptance.
| Decision | What to do | Evidence to retain |
|---|---|---|
| Problem statement | For D971X Wafer Butterfly Valve, define the required system outcome, failure consequence and measurable acceptance before choosing hardware. | Functional requirement |
| Feasible routes | Compare at least the practical construction, material, sealing and actuation alternatives, including reasons for rejection. | Option and trade-off matrix |
| Boundary conditions | Check every normal, transient, startup, shutdown, maintenance and utility-loss case that can change the solution. | Approved application data |
| Validation | Connect each claimed benefit to a calculation, drawing, qualification, inspection or package-level test that applies to the order. | Verification and evidence plan |
How this D971X Wafer Butterfly Valve guide should be used
This page does not claim that a named person, certificate, qualification, installed project or performance result applies to a future order. Product compliance is confirmed only when the accepted quotation, approved drawing, procedures and final manufacturing/test records identify the supplied configuration.
Technical requirements and standards can change. Verify the official source, contract edition, project precedence and purchaser options. See our technical content review and evidence policy, company information, inspection approach or submit a correction or application question.
D971X Wafer Butterfly Valve questions
What information is required to select a D971X Wafer Butterfly Valve?
Provide the medium and composition, all pressure and temperature cases, nominal size, flow or differential pressure where relevant, required function, end connections, materials, shutoff criterion, operation, standards, inspection and documentation. For this configuration, the review must specifically address compact installation between flanges with disc-clearance and gasket controls.
Which standards apply to a D971X Wafer Butterfly Valve?
The answer depends on the product construction, project jurisdiction and purchaser specification. A product standard may cover design scope while separate standards govern pressure-temperature rating, dimensions, ends, pressure testing, fire safety, emissions or materials. A wafer body may not provide independent downstream isolation; piping procedures must reflect the design.
How should D971X Wafer Butterfly Valve pressure and leakage testing be specified?
State the governing standard and approved edition, shell and closure basis, medium, pressure, duration, leakage acceptance, directionality, instruments, witness points and report format.
Can a D971X Wafer Butterfly Valve be supplied with an actuator?
Yes when the valve/actuator interface and load cases are engineered together. Define safe state, utility loss, speed, frequency, accessories, feedback, interlocks and assembly-level testing.
When should a D971X Wafer Butterfly Valve not be selected?
Do not select it when its qualified construction cannot satisfy the process, shutoff, materials, dynamics, maintenance or documentation requirements. Check disc clearance, installation orientation and transient loads; a nominal flange fit does not prove that the disc can open safely. The alternative should be chosen only after comparing the complete service duty.
English 
German 
Arabic 
French 
Spanish 
Italian 
Portuguese 
Russian